Haier Refrigerator Error Codes

Correspondence table of refrigerator malfunction codes:

Error Code	Content	Position of sensor	Item
F2	RT SNR short circuit or open circuit	Door body	RT SNR error
F3	R SNR short circuit or open circuit	Air duct of refrigerating chamber	R SNR error
F4	F SNR short circuit or open circuit	Air duct of freezerchamb er	F SNR error
F5	S SNR short circuit or open circuit	Air duct of chiller chamber	S SNR error
F6	D SNR short circuit or open circuit	Evaporator	D SNR error
E0	No signal, More than 2 minutes	/	Communication error
E1	No signal, More than 10 seconds	/	F FAN error
E2	No signal, More than 10 seconds	/	C FAN error
Ed	D SNR Can’t reach 8℃, 90 minutes	/	Defrosting error

When the refrigerator runs abnormally, it can enter into the mode of malfunction check by manually adjusting the display board.

Entering method: Open the refrigerator door,after the display board is lighted, press the key of “Temp Zone”, and at the same time press the key of “Temp Set” 5 times to enter into the mode of malfunction code and sensor temperature display. After entering into this mode, it will display the malfunction code in the temperature display area according to display priority level. Press the key of “Temp Set” to display next code. After the malfunction code is displayed, every time you press the key of “Temp Set”, it will display AT SNR, R SNR, S SNR, F SNR, D SNR practical temperatures one by one. Notes: if no malfunction, then it will display the practical temperatures of each sensor directly after entering. The following table shows the display methods of each sensor:

SNR, R SNR, S SNR, F SNR, D SNR

Notes: when checking the practical temperature of each sensor, distinguish the name of the presently displayed sensor according to the above table. The temperature display area of “-88” displays the integer figures of the practical temperature of the current sensor. One decimal figure of the practical temperature is displayed through 4 functional icons as shown in the following table:

Log-out method: after entering into this mode, press the key of “Temp Zone” again for 3 seconds to log out from this mode. If there’s no key press operation for 2minutes after entering into this mode, it will log out automatically

Troubleshooting

Problem: Moisture accumulates on the refrigerators inner walls

Cause:

1. Hot and moist climate.
2. The door is not closed tightly
3. The door is opened too frequently or for too long time

Solution:

1. Accumulation of frost and moisture accelerate in such climate.
2. Make sure the refrigerator is level and there is no food or container interfering with the door
3. Do not open the door so frequently

Problem: Moisture accumulates on the refrigerator’s outside surface or between two doors

Cause:

1. Damp climate
2. The refrigerator door is not closed tightly. This causes mixing of the cold air in the refrigerator with the warm air outside it

Solution:

1. It is normal in damp climate. The moisture will decrease when the humidity drops.
2. Make sure the refrigerator is level and there is no food or container interfering with the door

Problem: The compressor does not work

Cause:

1. The refrigerator is in defrosting cycle.
2. The refrigerator is not plugged into a power outlet.
3. The refrigerator is in OFF state.

Solution:

1. It is normal for an automatic defrosting refrigerator.
2. Verify the plug is plugged in the socket firmly.
3. Press the “Power” button for 3 second or more to restart the refrigerator or turn the knob from OFF to temperature selection position

Problem: The fridge storage compartment does not work

Cause:

1. The air door cable is not connected properly.
2. The fan does not work
3. The fridge storage compartment is turned of

Solution:

1. Check if the air door cable is not connected properly and install it correctly if not so. Verify that the air door acts normally with the Fridge ON/OFF key on the display panel
2. The fan does not work while the refrigeration air door is open. Please check if the door on-off behind the front decoration strip is installed properly. Reinstall it correctly if not so.
3. Turn on the fridge storage compartment manually

Problem: Too high temperature in the fridge/freezer storage compartment

Cause:

1. The door is opened too frequently or for too long periods of time
2. Temperature is set too high
3. The door is not closed tightly
4. The condenser is dirty

Solution:

1. Warm air will enter the refrigerator whenever the door is opened. Try to open the door as infrequently as possible.
2. Reset the temperature.
3. Make sure the refrigerator is on a level surface and there is no food or container interfering with the door.
4. Clean the condenser.

Problem: The temperature in the freezer storage compartment is too high while the temperature in the fridge storage compartment is OK

Cause: The temperature is set too high

Solution: Set the freezer temperature lower. It takes 24 hours for the temperature of the refrigerator to become stable.

Problem: The temperature in the fridge storage compartment is too high while the temperature in the freezer storage compartment is OK

Cause: The temperature is set too high

Solution: Set the fridge temperature lower. It takes 24 hours for the temperature of the refrigerator to become stable.

Problem: The inside of the refrigerator is dirty

Cause:

1. The inside of the refrigerator needs cleaning
2. Food with strong odor is stored in the refrigerator

Solution:

1. Clean the internal of the refrigerator
2. Wrap the food tightly.

Problem: If you hear beeps

Cause:

1. The fridge storage compartment door is open
2. The temperature in the freezer storage compartment is too high

Solution:

1. Close the door or silence the alarm manually
2. The alarm is normal when it is first started due to relatively higher temperature.

Problem: If you hear abnormal sound

Cause:

1. The refrigerator is not located on a level surface
2. The refrigerator touches some object around it

Solution:

1. Adjust the feet to level the refrigerator.
2. Remove objects around it.