Bosch Refrigerator Error Codes
Warning messages via the display
If several warning messages are displayed simultaneously, deal with each message individually. While a warning message is displayed, buttons cannot be pressed.
Sensor fault: DOOR OPEN Alarm.
Cause: An appliance door has not been closed properly or has been open too tong.
Remedial action: Ctosethe door. The display goes out.
Sensor fault: E01 alarm
Cause: A technical defect is possible.
Remedial action: Conduct an appliance self test.
Sensor fault: LOW POWER alarm
Cause: The mains voltage has dropped below the permitted limit value.
Remedial action: Buttons cannot be pressed. When the mains voltage reaches the stipulated value again, the warning message goes out. If the warning message is prolonged, inform your power supply company.
Fault: Appliance has no cooling capacity. The interior light does not function. The display does not come on.
Possible cause: Powerfailure; the fuse has actuated; he mains plug is not in properly
Remedial action: Checkthat the power is on. The fuse must be switched on. Checkthat the mains plug is plugged in.
Fault: The refrigerating unit switches on more and more frequently and for longer.
Possible cause:
- Appliance dooropened frequently.
- Largequantities of fresh food placed in the appliance
- The ventilation openings are covered
Remedial action:
- Do not open the door unnecessarily
- Switch on Superfunction
- Removeobstaclesand dirt
Fault: The temperature in the refrigerator compartment is too cold.
Possible cause: Temperature has been set too tow.
Remedial action: Set a warmer temperature.
Fault: The interior light does not function.
Possible cause:
- The bulb is defective
- The light switch is sticking
Remedial action:
- Changethe bulb
- Check whether it can be moved
Fault: The appliance is giving off odors.
Possible cause: Strong-smeltingfoods have not been packed in airtight containers
Remedial action: Cleanthe appliance. Pack strong-smeltingfoods in airtight containers
Fault: Temperature differs greatly from the set value.
Remedial action: In certain cases it may be enough to switch off the appliance for 5 minutes. If the temperature is too high, wait a few hours and check whether the temperature has approached the set value. If the temperature is too low, check the temperature again the next day.
Fault: Displays do not illuminate.
Possible cause: Power cut; the fuse has tripped; the mains plug has not been inserted properly.
Remedial action: Connect the mains plug. Check whether the power is on, and check the fuses.
Fault: Temperature display indicates “E..”.
Possible cause: Electronics have detected a fault.
Remedial action: Call customer service.
Fault: Warning signal sounds, alarm button 5 lights up. The freezer compartment is too warm! Frozen food is at risk!
Possible cause:
- Appliance is open
- Ventilation openings have been covered
- Large quantities of fresh food are being frozen
Remedial action:
- To switch off the warning signal, press the alarm button 5
- Close the appliance
- Ensure that there is adequate ventilation
- Freeze less fresh food
- When the fault has been eliminated, the alarm button 5 goes out shortly afterwards
Fault: Temperature display freezer compartment 4 flashes
Possible cause: A fault caused the freezer compartment to become too warm in the past.
Remedial action: When the alarm button 5 is pressed, the temperature display 4 stops flashing. The temperature display indicates for five seconds the warmest temperature which was reached in the freezer compartment
Fault: Appliance is not cooling, temperature display and light are lit.
Possible cause: Showroom mode is switched on.
Remedial action: Start appliance self-test (see chapter Appliance self-test). When the program has ended, the appliance switches over to normal operation.
Bosch Icemaker Fault Display
If an error code occurs do the following control according to the following action list.
| Error Codes | Problem |
|---|---|
| 1 1 1 | Ice production cycle is interrupted. |
| 1 2 1 | Ice production cycle is interrupted. |
| 1 3 1 | Ice production cycle is interrupted. |
| 1 4 1 | Ice tray heater or icemaker electronic is faulty. |
| 2 1 1 | Sensor fault in ice maker |
| 2 2 1 | Sensor fault in ice maker. |
| 2 3 1 | Internal ice maker fault. |
| 2 4 1 | Self Test Failed as Door was open. |
| 3 1 1 | Internal ice maker fault |
| 3 1 2 | Icemaker motor faulty |
| 3 1 3 | Water valve of icemaker faulty |
| 3 1 4 | Ice tray heater is faulty. |
| 3 1 5 | Icemaker inlet water heater problem. |
| 3 2 1 | Internal ice maker fault |
| 3 2 2 | Icemaker motor faulty |
| 3 2 3 | Water valve of icemaker faulty |
| 3 2 4 | Ice tray heater is faulty. |
| 3 2 5 | Icemaker inlet water heater problem. |
| 3 3 2 | Internal ice maker fault |
| 3 3 3 | Internal ice maker fault |
| 3 3 4 | Internal ice maker fault |
| 3 3 5 | Internal ice maker fault |
| 3 4 2 | Internal ice maker fault |
| 3 4 3 | Internal ice maker fault |
| 3 4 4 | Internal ice maker fault |
| 3 4 5 | Internal ice maker fault |
| 4 1 1 | Internal ice maker fault |
| 4 2 1 | Internal ice maker fault |
| 5 1 1 | Main voltage is to high. Check main voltage |
| 5 2 1 | Main voltage is to low. Check main voltage |
| 5 3 1 | Internal ice maker fault |
| 5 4 1 | Internal ice maker fault |
| 5 5 1 | Internal ice maker fault |
Cleaning
The Crisper Drawers and Chiller Drawer can be removed for cleaning.
- Unplug the appliance or turn off the circuit breaker.
- Remove all food from the appliance and store in a cool location.
- Clean the appliance with a soft cloth, using lukewarm water and a small amount of pH-balanced dishwashing liquid.
- Rub dry when done.
- Wipe the door seal with clear water only and then thoroughly wipe dry.
- After cleaning, reconnect to switch on the appliance.
Solving simple noise problems
- The appliance is not level: Align the appliance using a level. Use the height-adjustable feet.
- The appliance is touching adjacent units or appliances: Move the appliance away from adjacent units or appliances.
- Loose or sticking drawers, baskets or storage areas: Check the removable parts and, if required, reinsert them.
- Receptacles are touching each other: Move bottles or receptacles slightly away from each other